Intro -- Power and Energy Systems III -- Preface, Committees and Sponsors -- Table of Contents -- Chapter 1: Research and Design of Machinery in Energy Industry and Energy Technologies for Industry -- Prediction of Vehicle Fuel Consumption Model Based on Artificial Neural Network -- DeNOx Technology Selection and Optimal Design of SNCR System for a 300MWe CFB Boiler -- Design and Development of 850t/h CFB Boiler with Energy Saving Technology -- Evaluation the Role of Multi-Stage Compression and Waste Heat Recovery on Compressed Air Energy Storage System Performance -- Appropriate Electric Energy Conservation Measures for Big Mosques in Riyadh City -- Bayesian Algorithm Based on Airborne Power Supply System -- Study on the Cooling System of Super-Capacitors for Hybrid Electric Vehicle -- A Charging Management of Electric Vehicles Based on Campus Survey Data -- Back-EMF Position Detection Technology for Brushless DC Motor -- Stress State of Turbine Blade Root and Rim Considering Manufacturing Variations -- Analysis on a Gas Turbine Sealing Disk Structure and Material Strength -- A Kind of Adjustable Electric Heating Pipe Power Electrode Preparation Equipment -- Fracture Failure Mechanism Analysis of LP Second Stage Blades of a Gas Turbine -- Effect of Temperature Cycling on Stress Relaxation Behavior of Electrical Connector Contacts -- Loss Analysis and Calculation Method of the Switched Reluctance Motor -- Research on Characteristics of Variable Pitch Offshore Wind Turbine -- Analysis of Plastic Optical Fiber Based Daylight System Suitable for Building Applications -- Design and Performance of Horizontal Axis Wind Turbine Using Blade Element Momentum Theory (BEMT) -- Optimization of Multi-Pole Permanent Magnet Synchronous Generator Based 8 Blade Magnetically Levitated Variable Pitch Low Speed Vertical Axis Wind Turbine.

Effects of Double Glazing on the Performance of a Solar Thermal Collector -- Extended Modulation Index with more Eliminated Low Order Harmonics at Cascaded Multilevel Inverters -- Thermal Structure Analysis and Optimization of the Feeding System of the Permanent Magnet Linear Synchronous Motor -- Experimental and Validation of Photovoltaic Solar Cell Performance Models in Desert Climate -- Simulation on Building Energy Consumption for a Residential Building -- An Estimation Strategy of Lithium Battery SOC Based on Gauss-Hermite Filter -- Chapter 2: HV Power Lines Technologies -- Research on Prediction Model of Discharge Voltage under High-Altitude Condition Based on BP ANN -- Test Research on Phase-to-Ground Air-Gap Discharge Characteristics of UHV Substation -- The Simulation Study of Transformer Inductive Oscillating Switching Impulse Voltage Generation -- Research on the Failure Prediction of Electrical Connectors at High Temperature -- Research on an Accident of 500 kV Gas Insulated Transmission Line -- Management System of Transmission Line Passage Protection Based on Web Map Service -- PD Characteristics in Transformer Oil under AC Condition -- Research on Low-Temperature Reliability of Electrical Connectors -- Study on Failure Frequency of Sensitive Equipment Caused by Voltage Sag -- Evaluation of Voltage Sag Mitigation by Resonant Grounding Comparing to Existing Direct Grounding in Provincial Electricity Authority -- Research on an Online Monitoring and Diagnosis System of High-Voltage Circuit Breaker -- Assessment of Power Transformers Technical State Based on Technical Diagnostics -- A Novel Research and Implementation of Dynamic Voltage Restorer -- Parameter Design and Dynamic Characteristic Analysis of Magnetic Force Actuator Based on Visual Basic Interface Programming.

Chapter 3: Innovative Materials and Chemical Technologies for Power Industry and Energy Systems -- Study of μс-Si:H Thin Films Prepared by RF-PECVD -- An Assessment of Interatomic Potentials for Yittria-Stablized Zirconia -- Direct Electrochemical Reduction of Solid TiO2 in [BMIM]BF4-CaCl2 Ionic Liquid -- Synthesis of Ni0.6Cu0.4Fe2O4 Ferrite Fine Powder Using Egg White Method -- Synthesis of Fe3O4 Nanotubes under Assistance of Microwave by Tuning Chemical Deposition Mechanism and its Magnetic Properties -- Corrosion Resistance of Sintered NdFeB Magnets with Various Surface Coatings -- Preparation and Characterization of Conductive Filler Used for Electromagnetic Shielding Materials -- Analyzing of Energy Band and Density of States of ZnO -- Fabrication of Porous Titanium Dioxide Film by Oxidization of Titanium Foil and its Photocatalytic Performance for Degradation of Methyl Orange -- Characterization of TC-3 Glass/Fused Silica Composites for LTCC Applications -- New Method to Fabrication 3D Micro-Device Structures -- Polymer Stabilized Undoped and Copper Doped Cadmium Sulphide Nanoparticles: Polymer Crosslinked, Optical, and Thermal Stability -- Preparation and Gas Sensing Properties of Microrod ZnO Materials -- Design of Photonic Crystals Waveguide Using Microfluidic Infiltration -- Compact Modeling of Lightly Doped Nanoscale DG MOSFET Transistor -- Controlled Morphologies of Nanostructured ZnO Films by MOCVD Method -- Optimization of Abrupt Profile of Germanium in Si/SiGe Heterojunction Bipolar Transistor Specified for Radio Frequency Range Systems -- Graphene/Nylon-6 Chemiresistor Sensor for Trimethylamine Gas Sensing -- Preparation and Analysis of Novel Thermoelectric Material (SrxCa1-x)3Co4O9 -- Effects of Surface Treatment on the Performance of PEDOT: PSS/n-GaN Schottky Solar Cells.

The Study about Combustion and Emission Characteristics of n-Butanol/Diesel Fuel Mixture -- Effect of Partial Pressure of Precursors on Atomic Layer Deposited Zinc Oxide Films as TCO Material in Solar Cell Application -- Effect of V/Mo Ratio on Structural Properties of VxMo(1-x)Oy Nanoparticles Used as Alkaline Fuel Cell Catalyzer -- Biodiesel Production from Waste Vegetable Oils over MgO/Al2O3 Catalyst -- Energy Requirement Estimates for Two Step Ethanolysis of Waste Vegetable Oils for Biodiesel Production -- Hot-Corrosion Behavior of Modified YSZ Thermal Barrier Coating -- Three Dimensional Computational Fluid Dynamics Modelling of High Temperature Polymer Electrolyte Fuel Cell -- Preparation and Electrochemical Performance of Praseodymium Doped SnO2 Particles as Negative Electrode Material of Lithium-Ion Battery -- Atomic Layer Deposition of Molybdenum Oxide for Solar Cell Application -- Biodiesel Production Unit from Lab Scale to Industrial Pilot Plant: Material and Energy Balance -- Simulation of South African Corncob Gasification with Aspen Plus: A Sensitivity Analysis -- A New Type Mold Shell Used for Turbine Blade Production -- Electromagnetic Materials Design for the Enhancement of the Microwave Power Transmission through Polymeric Slabs -- Chapter 4: Innovative Design, Engineering Management and Automation of Modern Energy Systems -- A Survey on Single-Phase Faulty Line Selection Techniques for Small Current Grounding System in Medium-Voltage Grid -- Research on Separation of PD Signals Originated from Different Sources in Substation -- An Advanced Modeling and Control Approach for Frequency Regulation in Electric Energy Systems with New Resources -- A New Differential Relay Framework for Power Transformer -- Fuzzy Based Intelligent Approach to AGC of Multi-Area Multi-Unit Power System with SMES under Random Load Disturbances.

The Research and Implementation of the Mid-Frequency Power -- The Research of CDEGS in Defect Diagnosis for Grounding Grid -- Impact of Gas Turbine Frame Size on Efficiency of Gas Turbine Power Plants -- Power Management of Server Farms -- Location and Size of Distributed Generation Using Ant Colony Optimization -- Optimal Operation of Micro-CHP Systems for a Single-Family House in Italy -- An Experimental Setup Design to Evaluate Power Generation Performances of TECs under Different Temperatures -- Distribution Network Reconfiguration Optimization Method for Reducing the Voltage Sag Impact on Important Loads -- Study of Super Short-Term Bus Load Forecasting Model Based on Similar Ranges -- Single-Ended Forward Switching Power Supply Design Based on UCC2800 PWM Controller -- Disturbance Elimination of Buck-Converter with Resonant LPF via ILQ Servo-System -- The Design of Airport Flood Lighting Energy-Saving Control System -- Study on Frequency Characteristics of Valve in Heat Metering Control System -- Study on the Resistance Characteristics of Heat Metering System Based on Electric Valve -- Copper Electrolytic Cycle Reverse Current Control System -- The Study of CAN Buffer Multiplexing Technique and its Realization in TTC200 Controller -- Development of the Low Cost Harmonic and Power Instrument by Using Fourier Series Method with Microcontroller -- Imprecise Risk Assessment of Power System -- Power Equipment Technical State Assessment Principles -- The Optimal Operation of Super High Head Hydropower Station with Multiple Water Supply Modes -- Application and Contrast Analysis of BP and RBF Neural Network in Short-Term Wind Power Prediction -- An Analysis of Wind Speed Distribution at Benina, Benghazi, Libya -- Geodynamic Monitoring in Area of Nuclear Power Plant -- Potential of Renewable Energies Integration in an Essential Oils Extraction Process.

PerformanceAnalysis of Integrated Solar Combined Cycle Power Plant for Dhahran, Saudi Arabia.

Collection of selected, peer reviewed papers from the 2013 3rd International Conference on Power and Energy Systems, November 23-24, 2013, Bangkok, Thailand. The 106 papers are grouped as follows: Chapter 1: Research and Design of Machinery in Energy Industry and Energy Technologies for Industry; Chapter 2: HV Power Lines Technologies; Chapter 3: Innovative Materials and Chemical Technologies for Power Industry and Energy Systems; Chapter 4: Innovative Design, Engineering Management and Automation of Modern Energy Systems.

Description based on publisher supplied metadata and other sources.

Electronic reproduction. Ann Arbor, Michigan : ProQuest Ebook Central, 2018. Available via World Wide Web. Access may be limited to ProQuest Ebook Central affiliated libraries.